 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Silicore TONE RINGER GENERAL DESCRIP TION The SC9106 is a bipolar integrated circuit designed for teleph on e bell replace ment. SC9106 Outline Dra wing FUNCTIONS Two oscillators Output amp lifier Power supply control circuit FEATURES Designed for telephone bell replacement. Low current drain. Small size 'MINIDIP' p ackag e. Adjustable 2-frequency tone. Adjustable warbling rate. Built-in hysteresis prev ents false triggering and rotary dial 'CHIR PS'. Extension tone ringer modules. Alarms or other alerting devices. Adjustable for reduced supply initiation cu rrent. DIP-8 BLOCK DIAGROM 4 7 HIGH OSC 6 Vcc 3 LOW OSC AMP 8 OUT INTR TLF 1 POWER SUPPLY WITH HYSTERESIS PIN CONNECTION 1 2 8 OUT 7 T HF SC9106 3 4 (c) 6 T HF TLF 5 GND 5 2 SHAOXING SILICORE TECHNOLOGY CO.,LTD www. Silicore. com. cn 1/5 CHMC Silicore MAXIMUM RATINGS Characteristics Supply Voltage Power Diss ipation Operating Te mperature Storage Temp erature Symbol Vcc PD Topr Tstg SC9106 Value 30 400 -45~70 -65~150 Unit V mW C C ELECTRICAL CHARACTERISTIVCS (Ta=25C) (All voltage referenced to GND unless otherwise specified) Characteristic Operating Supply Vo ltage Initiation Supply Vo ltage *1 Initiation Supply Current *1 Sustaining Vo ltage *2 Sustaining Current *2 Output Vo ltage High Output Vo ltage Low IIN(Pin 3) IIN(Pin7) High Frequency 1 High Frequency 2 Low Frequency Test condition See Fig.2 6.8k-Pin 2 to GND See Fig.2 No load Vcc=Vsus, see Fig.2 Vcc=21V, I8=-15mA Pin6=6V, Pin7=GND Vcc=21V, I8=15mA Pin7=6V, Pin6=GND Pin3=6V, Pin4=GND Pin7=6V, Pin6=GND R3=191k, C3=6800pF R3=191k, C3=6800pF R2=165k, C2=0.47F Symbol Min Typ Max Unit Vcc Vsi Isi Vsus Isus VOH VOL 17 1.4 9.7 0.7 17 19 2.5 11 .0 1.4 19 29 21 12 2.5 21 1.6 500 500 fH1 FH2 fL 461 512 563 576 640 9.0 10 704 11 V V V mA V V nA Hz Hz Hz 4.2 mA * Note (see electrical characteristics sheet) 1. Initiation supply voltage (Vsi) is the supp ly voltage required to start the to ne ringer oscillating 2. sustaining voltage (Vsu s) is the supply voltage required to maintain oscillation. SHAOXING SILICORE TECHNOLOGY CO.,LTD www. Silicore. com. cn 2/5 CHMC Silicore TEST CIRCUIT _ A 6.8K 3 + 0.47uF _5% _ 165K + 1% S1 4 S2 1 2 8 SC9106 SC 9106 7 _ 191K +1% 0.068uF _ 5% + 6 5 APPLICATION CIRCUIT C1 R1 1 TIP 0.9uF 560 4 2 C5 1 RSL 2 3 D1 29V R2 _ 165K+1% C2 _ 0.47uF+5% 4 8 0.22uF 7 10K + 191k _ 1% C3 R3 _ 6.9nF+5% 15K SP 3 RING SC9106 6 5 C4 22uF/35V 1300:8 APPLICATION NOTE The application circuit illustrates the use of th e UTC9106 device in typical teleph on e tone ringer application. The AC ring er signal vo ltage appears across the TIP and RING inputs of the circuit and is attenuated by capacitor C1 and resistor R1. C1 also prov ides isolation from DC voltage (48V) on the exch anged line. After full wave rectification by th e bridge diode, the waveform is filtered by capacitor C4 to provide a DC supp ly for the tone ringer chip. As this voltage exceeds the initiation voltage (Vsi), oscillation starts. SHAOXING SILICORE TECHNOLOGY CO.,LTD www. Silicore. com. cn 3/5 CHMC Silicore 640 Hz (fH2) at 10Hz (fL) rate. SC9106 With th e components shown, th e ou tput frequency chops between 512Hz (fH1 ) and The loudspeaker load is coupled th rough a 1300W to 8W transformer. The ou tput coupling capacito r C5 is required with transformer coupled lo ads. When driving a pizeo-ceramic transducer type load , th e coupling C5 and transformer (1300:8) are not required. However, a current limiting resistor is required. The low frequency oscillator oscillates at a rate (FL) controlled by an external resistor (R2) and capacitor (C2). The frequency can be determined using the relation f L =1/1.289 R2* C2. The high frequency oscillates at a fH1 , fH2 controlled by an external resistor (R3) and capacitor (C3). The frequency can be determined using the relation fH1 =1/1.504 R3*C3 and fH2 = 1/1.203 R3*C3. Pin 2 of the SC9106 allo ws conn ection of external resistor RSL, which is used to program th e slope of the supply current vs supply vo ltage characteristics (see Fig.3), and hence th e supply cu rrent up to the initiation voltage (Vsi). This initiation voltage remains constant independent of RSL. The supply current drawn prior to triggering varies inversely with RSL, decreasing for increasing value of resistance. Thus, increasing the value of RSL, will decrease the amount of AC ringing current required to trigger th e device. As such, longer subscriber loops are possible since less voltage is dropped per unit length of loop wire due to the lower current level. RSL can also be used to co mp ensated for smaller AC coupling capacitors (C5 on application circuit) (higher impedance) to the line which can be used to alter th e ringer equivalence numb er of a tone ringer circuit. The graph in Fig.3 illustrates the variation of supply current with supply voltage of the SC9106. Three curves are drawn to show the variation of in itiation cu rrent with RSL. Curve B ( RSL=6.8k ) shows the I-V characteristic fo r SC9106 tone ringer. Cu rve A is a plot with RSL<6.8k and sh ows an increase in the cu rrent drawn up to the initiation voltage Vsi. The I-V characteristic after initiation re mains unchanged . Curve C illustrates the effect of increasing RSL ab ove 6.8kW in itiation current decreases but again current after triggering is un changed. SHAOXING SILICORE TECHNOLOGY CO.,LTD www. Silicore. com. cn 4/5 CHMC Silicore CHARACTERISTICS CURVES SC9106 Fig.2 Fig.3 SHAOXING SILICORE TECHNOLOGY CO.,LTD www. Silicore. com. cn 5/5 CHMC |
Price & Availability of SC9106
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |